Go Back   Maxum Boat Owners Club - Forum > Maxum Specific > Sport Boats
Click Here to Login
Register FAQ Community Calendar Today's Posts Log in

Reply
 
Thread Tools Search this Thread Display Modes
 
Old 03-31-2021, 09:59 AM   #1
Lt. Commander
 
Join Date: Feb 2018
Location: New Jersey
Posts: 142
Default wont start

started boat up after winter storage and all good. Turned key to accessory and alarm ring goes on and then turn key to start and worked fine. Did this a few times during the day after checking all items out. Then later in day when I re-started there was no no alarm from accessory and no start when key is turned fully. All trim tabs work, engine tilt up and down still works, power to everything but no sound of anything after turning the key.

Any idea. Thanks

Mark
__________________

stock333 is offline   Reply With Quote
Old 03-31-2021, 11:44 AM   #2
Captain
 
Join Date: Dec 2015
Location: Florida
Posts: 522
Default

Start with the simple stuff.

Is the kill lanyard firmly attached?
Shifter in neutral?

The rest will depend on what engine you have.. Please post details.
__________________

jparsons121 is offline   Reply With Quote
Old 03-31-2021, 01:15 PM   #3
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,606
Default

Drive trim and trim tabs are powered directly from the battery. After checking the run/stop (kill) switch and verifying being in neutral check for power at the "B" terminal of the ignition switch.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2

Mike
mmwjr is offline   Reply With Quote
Old 04-09-2021, 10:04 AM   #4
Lt. Commander
 
Join Date: Feb 2018
Location: New Jersey
Posts: 142
Default

Did not reply sooner because changed the ignition switch and it started. Now the same thing is happening. Radio works, trim taps work, engine tilt works but nothing when key is turned. Engine is 5.0 EFI Mercrusier.
Thanks
stock333 is offline   Reply With Quote
Old 04-09-2021, 11:37 AM   #5
Captain
 
Join Date: Dec 2015
Location: Florida
Posts: 522
Default

If you have power at the B terminal as mike previously mentioned, next is the slave solenoid Check to see if you have power on the small yel/red terminal on the slave solenoid when the key is turned to Start position.

If so, check to see if you have power out of the solenoid on the large yellow/red terminal. (again with key turned to start position)

Solenoid is mounted on the top of the engine next to the red circuit breaker button.
jparsons121 is offline   Reply With Quote
Old 04-09-2021, 12:53 PM   #6
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,606
Default

If no power on the “B” terminal of the ignition switch check the 10 pin connector on the engine harness to verify it’s fully connected.
__________________

__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2

Mike
mmwjr is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Powered by vBadvanced CMPS v3.2.3

All times are GMT. The time now is 05:22 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.