Go Back   Maxum Boat Owners Club - Forum > Maxum General > Projects and Customisations
Click Here to Login
Register FAQ Community Calendar Today's Posts Log in

Reply
 
Thread Tools Search this Thread Display Modes
 
Old 09-04-2014, 05:13 PM   #1
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default Project stainless thru hull

Going to start a separate thread....[ATTACH][/ATTACH][ATTACH][/ATTACH]
__________________

__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 09-04-2014, 05:14 PM   #2
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

I have the starboard side of the boat done....and I think 2 of these were the hardest of the whole project....[ATTACH][/ATTACH]
__________________

__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 09-04-2014, 05:18 PM   #3
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

Now the 7th one out of the ten is giving me a little resistance....[ATTACH][/ATTACH]

The whole is just a tiny bit too tight....having to thread it all the way in. Good news it's one of the largest, but on my hands and knees on the dock trying to screw it in is just about as bad as finishing it from the inside!!!!
__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 09-04-2014, 05:20 PM   #4
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

Just 3 more after this...2 behind the AC and 1 more large one for the galley sink. These are gonna wait for a fresh day to finish. The galley sink is prolly gonna be like the other large one. And it will require two people.....
__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 09-04-2014, 06:42 PM   #5
Moderator

 
shrew's Avatar
 
Join Date: Apr 2008
Posts: 5,691
Default

Wouldn't this have been easier with the boat hauled? I've never seen anyone take on this project while wet slipped.
shrew is offline   Reply With Quote
Old 09-04-2014, 07:10 PM   #6
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

Why add work to the project??? The real work is all done from inside the boat.
__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 09-04-2014, 09:53 PM   #7
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
Default

Max you do realize these pretty thru hulls make the rub rail, tank vents, .... all look so bad.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2

Mike
mmwjr is offline   Reply With Quote
Old 09-04-2014, 10:25 PM   #8
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

Mike, my rub rail and vents are stainless and chrome. This will really compliment the rest of the boat. Coule small projects after these.....replace anchor roller, replace anchor deck switch covers. My business is real slow during the hottest months of summer. Since its so hot out I have lots of free time on boat forums and amazon!!!!
__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 09-05-2014, 01:31 AM   #9
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
Default

Nothing like working on the boat during the hot season

It's going to look sharp when finished
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2

Mike
mmwjr is offline   Reply With Quote
Old 10-12-2014, 08:13 AM   #10
Lt. JG
 
Join Date: May 2013
Location: Lancaster, PA/Havre de Grace, MD
Posts: 42
Default

That is going to look nice when done. A couple thru hulls above the waterline need done for me and I thinking about going the SS route myself. What sealant did you use? Where did you buy the fittings?
rip131313 is offline   Reply With Quote
Old 10-13-2014, 01:19 AM   #11
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
Default

Rip I believe Max got the fittings from Amazon, since these are above the water line I would use 4200 sealant.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2

Mike
mmwjr is offline   Reply With Quote
Old 10-13-2014, 03:25 AM   #12
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

Rip.....I was fully expecting these thru hulls to be super hard to remove from the hull even after nut was removed!! Of all things maxum decided not to use that freaky strong sealant on the thru hulls!! Once the nut was removed these slid right out of the hull. Since maxum didn't use sealer, I didn't put anything on the new stainless ones. I was fully prepared use some 4200. I did however take my time and make sure the nuts were very tight when I installed the new ones.
__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 10-15-2014, 03:11 AM   #13
Lt. JG
 
Join Date: May 2013
Location: Lancaster, PA/Havre de Grace, MD
Posts: 42
Default

Thanks for the advice Mike. Max it's good to hear that your removals were easy. If I redo them I have 18 thru hulls with 17 of them being plastic!
rip131313 is offline   Reply With Quote
Old 10-15-2014, 04:18 AM   #14
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

Rip.....let me be clear....removal was easy, access is another story!!! I spent a lot of time finding and preparing myself to get into unbelievable spots for access.....
__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 10-17-2014, 03:00 AM   #15
Captain
 
HavaMax's Avatar
 
Join Date: Jul 2009
Location: Lake Havasu City AZ
Posts: 832
Default

Rip.....18 thru hulls!?!? I had 10 total, can't believe you have that many!!
__________________
Dezart Elegance Pool Tile Cleaning
1994 Maxum 3200 SCR
HavaMax is offline   Reply With Quote
Old 10-17-2014, 05:50 PM   #16
Lt. JG
 
Join Date: May 2013
Location: Lancaster, PA/Havre de Grace, MD
Posts: 42
Default

Trust me ... I thought 18 was a lot too! I think anything that drains has a thru hull!
rip131313 is offline   Reply With Quote
Old 10-17-2014, 06:25 PM   #17
Admiral
 
Phillbo's Avatar
 
Join Date: Mar 2012
Location: Lake Powell
Posts: 1,613
Default

This project sounds like a good job for a midget with a second elbow just above his wrist
Phillbo is offline   Reply With Quote
Old 10-17-2014, 08:15 PM   #18
Captain
 
Kevlar7r's Avatar
 
Join Date: Aug 2014
Location: Jacksonville, FL
Posts: 746
Default

Quote:
Originally Posted by Phillbo View Post
This project sounds like a good job for a midget with a second elbow just above his wrist


saw that guy perform at a party once. Don't ask me why I was at THAT Kind of party.. .
__________________

Kevlar7r is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Powered by vBadvanced CMPS v3.2.3

All times are GMT. The time now is 07:31 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.