Go Back   Maxum Boat Owners Club - Forum > Maxum General > Electronics
Click Here to Login
Register FAQ Community Calendar Today's Posts Log in

Reply
 
Thread Tools Search this Thread Display Modes
 
Old 06-26-2015, 12:24 AM   #1
Lt. JG
 
Join Date: May 2015
Posts: 25
Default A/C issues after work

Hello all!

I have a 2004 Maxum 2400 scr. Yesterday I changed the impeller and gas filter. Also, I ran through a couple cycles of water as I was getting a red tint from the antifreeze at both the sink in the cabin and the one in the head. When I initially got out there, at about 2pm, I turned on the A/C and the cabin cooled to 65 degrees within an hour. Later on, after running the boat for a little while, I turned the A/C back on and was unable to get the temp in the cabin below 75. I noticed that not much air was coming out of the vents. I refilled the water tank and nothing changed. Any idea what I may have done/am doing wrong?

Thank you!!
__________________

Patrick88 is offline   Reply With Quote
Old 06-26-2015, 01:04 AM   #2
Captain
 
Kevlar7r's Avatar
 
Join Date: Aug 2014
Location: Jacksonville, FL
Posts: 746
Default

Could be a little low on Freon and froze up.



Run it again, and see if there is ice growing on the unit.



Your boat is in the water right? These ac units raw water to cool the condenser. Your water tank has nothing to do with the AC.
__________________

Kevlar7r is offline   Reply With Quote
Old 06-26-2015, 01:05 AM   #3
Lt. JG
 
Join Date: May 2015
Posts: 25
Default

Thank you for the help. Any advice or past thread you know of that speaks about how to charge the freon?
Patrick88 is offline   Reply With Quote
Old 06-26-2015, 01:07 AM   #4
Captain
 
Kevlar7r's Avatar
 
Join Date: Aug 2014
Location: Jacksonville, FL
Posts: 746
Default

It is R22, you will need a licensed ac tech.
Kevlar7r is offline   Reply With Quote
Old 06-26-2015, 01:08 AM   #5
Lt. JG
 
Join Date: May 2015
Posts: 25
Default

Good to know. Thank you again!
Patrick88 is offline   Reply With Quote
Old 06-26-2015, 01:09 AM   #6
Captain
 
Kevlar7r's Avatar
 
Join Date: Aug 2014
Location: Jacksonville, FL
Posts: 746
Default

See my edits above. Your boat is in the water, right?
Kevlar7r is offline   Reply With Quote
Old 06-26-2015, 01:10 AM   #7
Lt. JG
 
Join Date: May 2015
Posts: 25
Default

Oh, Yes, it's in the water. Where should I be looking for the ice buildup?
Patrick88 is offline   Reply With Quote
Old 06-26-2015, 01:12 AM   #8
Captain
 
Kevlar7r's Avatar
 
Join Date: Aug 2014
Location: Jacksonville, FL
Posts: 746
Default

On the unit itself. Not sure where yours is, mine is under the forward berth. It will be all over the evaporator, usually starts from the bottom and works up. Might take an hour or two to build up.
Kevlar7r is offline   Reply With Quote
Old 06-26-2015, 01:14 AM   #9
Lt. JG
 
Join Date: May 2015
Posts: 25
Default

Ok. I will run it tomorrow and see if I can locate the unit. I'll check the manual and see if I can find it.
Patrick88 is offline   Reply With Quote
Old 06-26-2015, 01:20 AM   #10
Captain
 
Kevlar7r's Avatar
 
Join Date: Aug 2014
Location: Jacksonville, FL
Posts: 746
Default

Even before ice builds up, there should be water droplets on the little tubes after its been running for a bit. That's normal.



If they look dry, touch them... Carefully. One will be cold, one will be very hot. If your finger sorta sticks a bit to the cold one, like when grab an ice cube out of freezer, it's probably running below freezing, meaning its low on Freon.
Kevlar7r is offline   Reply With Quote
Old 06-26-2015, 01:24 AM   #11
Lt. JG
 
Join Date: May 2015
Posts: 25
Default

Wow, such great info. I will let you know what I find tomorrow. Thanks!
Patrick88 is offline   Reply With Quote
Old 06-26-2015, 04:17 AM   #12
Admiral
 
mmwjr's Avatar
 
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
Default

The A/C is running on shore power?

Did you Check to verify the power cord is properly plugged in and not loose causing low voltage. Else what Kevlar7 said.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2

Mike
mmwjr is offline   Reply With Quote
Old 06-26-2015, 10:04 AM   #13
Lt. JG
 
Join Date: May 2015
Posts: 25
Default

No, I have not checked the power cord. I guess I had assumed it was plugged in properly, but I will check it out today when I get out there.

Thank you!
Patrick88 is offline   Reply With Quote
Old 06-26-2015, 12:19 PM   #14
CGG
Lt. Commander
 
CGG's Avatar
 
Join Date: Jul 2013
Posts: 186
Default

Change the A/C foam filter yearly.
CGG is offline   Reply With Quote
Old 06-26-2015, 12:28 PM   #15
Commander
 
Join Date: Jan 2014
Posts: 251
Default

make sure you are getting water flowing out of your through hull fitting. If not loosen the screws on the ac water pump which is located in the engine bay. Let it run and loosen the screws to let any air out. Also clean the screen.
Once in a while I have to bleed some air our of mine.
as noted here.. check for the unit freezing which usually indicated low R22.
Baby Blue is offline   Reply With Quote
Old 06-27-2015, 12:39 AM   #16
Lt. JG
 
Join Date: May 2015
Posts: 25
Default

Turned on the A/C today and it worked like new! I'm unsure what may have gone wrong, yesterday, but today it's good as new!

Thank you all for the insight. If I have any further issues, I will run through this checklist
Patrick88 is offline   Reply With Quote
Old 06-27-2015, 01:03 AM   #17
Captain
 
Kevlar7r's Avatar
 
Join Date: Aug 2014
Location: Jacksonville, FL
Posts: 746
Default

Well, if its low, it will run great for a couple of hours.... Untill it freezes up.
__________________

Kevlar7r is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Powered by vBadvanced CMPS v3.2.3

All times are GMT. The time now is 06:45 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.