|
11-10-2024, 02:52 PM
|
#1
|
Ensign
Join Date: Nov 2024
Posts: 8
|
Maxum SCR 2300 4.3 Mercruiser 175hp not revving more than 3000-3500 RPM
Hello guys,
I have a Maxum SCR 2300 from 1991 with Mercruiser 4.3L 175 HP paired with an Alpha One Gen 2 outdrive.
Took it out last week and saw that it does not rev more than 3000-3500 RPM.
There are no alarms, no engine weird sounds, idles good..
After 20-30 mins of going at 3000-3500rpm it just died at idle, cleaned 3 sparkplugs and it fired right back ( they were dirty, boat stood for more than a year ) .
What do you guys think it could be the cause ? I'm new on boating, especially Inboard engined since they are not really popular in my country ( Romania ).
Also what website do you guys use in order to purchase parts ?
Thank you alot for the help !
__________________
|
|
|
11-10-2024, 08:49 PM
|
#2
|
Admiral
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
|
Welcome aboard!
I had a 4.3 in a previous boat that ran ok and had a smooth idle but had no compression in one cylinder due to a bad exhaust valve. I would check the other plugs and perform a compression test. Is this a new to you boat? If not when did it last run good? How old is the fuel and have you changed the filter?
__________________
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2
Mike
|
|
|
11-10-2024, 08:54 PM
|
#3
|
Ensign
Join Date: Nov 2024
Posts: 8
|
Thanks alot for the tip.
Just bought the boat. The fuel is fresh, the last time it run was more than a year ago. They said the filter is changed and also fresh oil. Checked the oil it really is fresh, they did the oil change and did not go on the water with it.. I will go to the boat in a couple of days and change the sparkplugs (they look ok but decided just to get new ones).
|
|
|
11-10-2024, 10:11 PM
|
#4
|
Admiral
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
|
See if one plug looks different from the others. I take it you bought the boat without taking it for a sea trail? No one no no when buying a boat.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2
Mike
|
|
|
11-10-2024, 11:37 PM
|
#5
|
Ensign
Join Date: Nov 2024
Posts: 8
|
They are all the same, I bought it with a sea trial, they just said it's caused by the carburateur needing to be adjusted. The price was good and the boat is in a very good condition.. I just think it needs a bit of love cuz in the last 4 years it was only took out 2 times.. it has around 700 hours.
|
|
|
11-10-2024, 11:37 PM
|
#6
|
Ensign
Join Date: Nov 2024
Posts: 8
|
Now that you told me about your issue with one cylinder not working kinda got me worried. Will need to check
|
|
|
11-10-2024, 11:44 PM
|
#7
|
Admiral
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
|
I hope it is something simple but I have seen many folks here who were told it just needs,… only to find a much bigger issue. Best wishes.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2
Mike
|
|
|
11-10-2024, 11:50 PM
|
#8
|
Admiral
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
|
BTY do you know if the exhaust manifolds and risers were ever replaced? These as well as the engine are raw water cooled and if in salt water the exhaust typically needs to be replaced every 5 years. When they fail sea water gets into the exhaust stream and engine backpressure can draw the water into the cylinders which results in failure. This is what happened to the engine I had.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2
Mike
|
|
|
11-11-2024, 12:45 AM
|
#9
|
Ensign
Join Date: Nov 2024
Posts: 8
|
They were replaced 4 years ago when it came to Romania. The boat was not used in salt water.
|
|
|
11-11-2024, 12:56 PM
|
#10
|
Admiral
Join Date: Feb 2012
Location: Essex, Maryland
Posts: 10,632
|
Quote:
Originally Posted by silviuradu95
They were replaced 4 years ago when it came to Romania. The boat was not used in salt water.
|
Ok, that’s promising. With a boat this age it may be time to rebuild the carburetor. But I would first perform a compression test to verify the engines health.
__________________
1997 Silverton 362, 7.4 Crusaders
1997 2400 SCR, 5.7 Vortec / Bravo 2
Mike
|
|
|
11-11-2024, 01:45 PM
|
#11
|
Ensign
Join Date: Nov 2024
Posts: 8
|
Thank you very much for the help.
Will purchase a compression test kit and try to do it soon, will update once I do that.
Hopefully no compression issues
|
|
|
11-14-2024, 03:28 PM
|
#12
|
Lieutenant
Join Date: Jul 2023
Location: Croatia
Posts: 85
|
Hey silviuradu95
I'm from Croatia, and I own almost the same boat. It can be challenging to find parts for U.S. boats in Europe, but I can share some links to stores located in Croatia, Austria, and Germany.
|
|
|
11-14-2024, 03:34 PM
|
#13
|
Ensign
Join Date: Nov 2024
Posts: 8
|
Hello sir,
Would be awesome if you could share the links !!
Thank you !
|
|
|
11-14-2024, 03:46 PM
|
#14
|
Lieutenant
Join Date: Jul 2023
Location: Croatia
Posts: 85
|
Done, see PM
|
|
|
11-14-2024, 03:50 PM
|
#15
|
Ensign
Join Date: Nov 2024
Posts: 8
|
Thanks alot !!
__________________
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|